What volume of oxygen would be produced by this reaction 72.87 L of water were consumed? Step 1: The alkene reacts with aqueou... *Response times vary by subject and question complexity. a chemist reacts 8.85g or iron with an excess oh hydrogen chloride to form hydrogen gas and iron(II)chloride.calculate the theoretical yield and the percentage yield of hydrogen if 0.27g H2 are collected *Chemistry. Problem: Hydrogen and iodine gases react to form hydrogen iodide gas as follows: H2 (g) + I2 (g) → 2HI (g) At a certain temperature and pressure 1.4 L of H 2 reacts with 1.4 L of I 2. Solution for Fluorine gas and water vapor react to form hydrogen fluoride gas and oxygen. OH Answer has a unit symbol, and is rounded to the correct number of significant digits. Fluorine gas and water vapor react to form hydrogen fluoride gas and oxygen. What volume of hydrogen fluoride would be produced by this reaction if 1.1 m of What volume of oxygen would be produced by this reaction if 8.7 mL of… REMEMBER: 1 mole of any gas at standard temperature (T) and pressure(P) (T = 273 K and P= 1 atm) occupies a volume (V) of 22.4 L. A link to the app was sent to your phone. Nitric oxide gas and liquid water are produced. A → B Solution for Fluorine gas and water vapor react to form hydrogen fluoride gas and oxygen. A reaction mixture contains 6.75 g Na and 3.03 g H2. Done another way without using moles since it is at STP: 4.8 cm3 F2 x 4 cm3 HF / 2 cm3 F2 = 9.6 cm3 HF, Elizabeth D. a. addition of hydrogen  answered  11/14/19, Ph.D. University Professor with 10+ years Tutoring Experience, 2F2 (g) + 2H2O (g) ---> 4HF (g) + O2 (g) ... balanced equation, Assuming STP (standard temperature and pressure) we know that 1 mole of and idea gas = 22.4 liters, 4.8 cm3 F2 x 1 L/1000 cm3 x 1 mol/22.4 L = 2.1x10-4 moles of F2, moles HF produced = 2.x10-4 moles F2 x 4 moles HF / 2 moles F2 = 4.3x10-4 moles, Volume of HF produced = 4.3x10-4 moles x 22.4 L/mole = 0.0096 liters = 9.6 cm3. 1/2N_2(g) + 3/2F_2(g) rarr NF_3(g) NF_3 is in fact not so nasty .... it is much safer than NCl_3 or NI_3.. Of course the direct synthesis with fluorine gas … C) cyclopente... A: The given compound is an alcohol. Hydrogen reacts w/ sodium to produce solid sodium hydride, NaH. Platinum is used as a catalyst. No packages or subscriptions, pay only for the time you need. c)How many grams of which reactant is left unreacted? 1) Write the Chemical Reaction. Fluorine gas and water vapor react to form hydrogen fluoride gas and oxygen. Identify the limiting reactant and determine the theoretical yield of ClF3 in grams.             The required answer is follow as : Q: Dehydration of the alcohol here produces what compound? The reaction takes place in 2 steps. water were consumed? The equation is unbalanced because the number of hydrogen atoms is not the same on both sides of the equation. A) cyclopentane F2 (g) + H2O (g) ----> HF (g) + O2 (g) 2) Balance the equation. B) pentane Also, be sure your answer has a unit symbol, and is rounded to the correct number of significant digits Identify an equation for the following reactions, balance each, and give the reaction type. Also, be sure your answer has a unit symbol, and is rounded to the correct number of significant digits, \$ X 2 Check & 0 В — А answered  11/14/19, Passion for Significance, Engineering, Science, Math and Creativity, F2 (g) + H2O (g) ----> HF (g) + O2 (g), 2F2 (g) + 2H2O (g) ---> 4HF (g) + O2 (g), REMEMBER: 1 mole of any gas at standard temperature (T) and pressure(P) (T = 273 K and P= 1 atm) occupies a volume (V) of 22.4 L, *** Assuming the reaction took place in standard temperature and pressure as it is not stated otherwise, A) Use the periodic table to obtain the Atomic Mass or the Atomic Weight of Fluorine (F2), Atomic Mass or Atomic Weight of F = 18.998 g F, Atomic Mass or Atomic Weight of F2 = 18.998 *2 = 37.996 g F2, B) Use the atomic mass and find the Molar Mass (MM) using our balanced equation and atomic mass, 4 moles of HF is balanced with our 2 moles of F2 in our equation, C) we are given 4.8 cm^3 but using our assumption of standard temperature and pressure we need to be in liters so we need to further use dimensional analysis to convert to the correct units, (4.8 cm^3 F2) x ( 1 mL / 1 cm^3) x ( 1 L / 1000 mL) x (1 mol F2/ 22.4 L) x (1 mol F2 / 37.996 g F2 ) x (4 mol HF / 2 moles F2) x ( 22.4L / 1 mol HF) * (1000 mL / 1 L) * ( 1 cm^3 / 1 mL) = V. We are only given two significant figures in the problem so our answer must be so: Get a free answer to a quick problem.